Bafang max drive clutch/ Bafang M400 finger freewheel for replacement; If your M400 MAX Drive is not smooth when pedaling, then consider the pawl clutch is defective.

This pawl clutch is also suitable for AEG MM G350 motor.

How to replace the Bafang Max drive M400 G330 pawl clutch, please check the video below:

Bafang M400 reduction gear for replacement; the Bafang max drive steel cover is included.

The item includes motor gasket, reduction gear and gear cover/motor casing as shown in the picture.

For how to replace the reduction gear cover, please refer to the following vedio.

Bafang max drive  M400 G330 motor controller(UART protocol) for replacement. If your motor is with CAN protocol, this controller will not fit. Please double check before ordering.

The Bafang M400 controllers has several parameters, 36V 250W, 36V 350W, 43V 350W or 48V 350W controllers, please check your own motor before placing the order.

If you want a headlight for your bike, you can add a pair Bafang MAX M400 G330 headlight/rearlight cable and a LED headlgiht with the controller.

Note: Coaster brake controller and standard e-brake controller are not compatible. Normally coaster brake motor will have  "CB" marks on the motor. If you are not sure your motor is standard e-brake motor or coaster brake motor, please email us, we will check for you. If you don't know how to identify, please check our picture. The coaster brake controller installs on e-brake motor, the coaster brake controller will be burned at once.

Bafang has two protocols for the max drive mid motor, UART or CAN protocol. How to identify? UART protocol controllers no need calibration; CAN protocol controllers may needs calibration. 

If the display connector is with triangle connector, then it is with CAN protocol. The back of the display may also mark “CAN” .

The controllers we are selling is with UART protocol and it will not fit for CAN protocol motor. please double check before ordering. 

If your original controller is 48V 13A, then you can choose 48V 13A controller for replacement. Bafang has upgraded to 13A controller for the 48V motor.

How to replace the Bafang Max drive M400 G330 controller, please check the video below:

Bafang Max drive MM M400 G330 axle with torque sensor;

The axle provided by Bafang fits for Bafang M400 G330 mid motor.

The length for the axle is 151mm.

There are two versions for Max drive mid motor, standard e-brake motor and coaster brake(pedal brake) mid motor; and the torque sensor for them are different.

There are two protocols for the torque sensors, CAN and UART protocol;  For how to identify the motor is UART or CAN protocol, please check our pictures on the M400 controller page. There is another way to identify. UART protocol torque sensor connectors are with the female connectors which are shown on our pictures; the CAN torque sensor is with the male connectors.

UART Bafang M400/G330 torque sensor e-brake model: MM G330.CB 1.8 TB33(some motor might be with different model name, please email us if you are confusing)

UART Bafang M400/G330  torque sensor coaster brake/pedal brake model: MM G330.CB 1.8 VB3

CANbus Bafang M400/G330 torque sensor e-brake model: SR PA212.32.ST.C

How to replace the Bafang max drive M400 G330 torque sensor, please check below video:

Bafang Max drive M400 /G330 barebone motor.

If your motor is "old age" and defective, you can buy a new barebone motor to replace it.

The are two protocols for Bafang G330/ M400 motor, UART and CAN, UART motor is with 3 pins speed sensor cable, and CAN motor is with 4 pins speed sensor cable, UART motor's display is round connector which CAN motor's display is triangle connector. If you don't know how to identify, please email us.   

How to check your max drive G330 motor is UART or CAN protocol? Check the original display connector, UART protocol is with round 5pin connector display which CAN protocol is with 5pin triangle connector display.

If you need complete set of Max drivec M400, please email us.

Bafang M400 G330 motor take apart:

Bafang max drive MM G330 Motor nylon gear with bearing for replacement；

There would be two versions for the Nylon gear, one is with 4mm gap depth, and the other is with 6mm gap depth.

The height of the bearing is 46mm with 4mm gap gear; the bearing height for 6mm gap gear is 44mm. The two Max drive bearing sets are not compatible. 

44mm gear set is the old version while 46mm gear set is the new version, please check your original bearing before placing the order.

The solo nylon gear only fits for 46mm gear set.

For details, please check the picture for the gear; please double check before placing order. 

Bafang Max drive core, including Bafang M400 stator or rotor for replacement.

Bafang M400 motor core is easy to disassemble and replace.

The Bafang MAX drive M400 G330 motor core are sourced directly from Bafang.

How to check your motor is CAN or UART protocol? Please check from the M400 controller or the Bafang display connector;

The UART protocol controller will have a "U" mark on the controller, it's EB-BUS connector is with female connector and the display for the motor would be UART protocol with a 5 pin round connector.
If the display connector is with triangle connector, then it is with CAN protocol. The back of the display may also mark “CAN".

Replacing the CAN motor core, you may need to recalibrate the motor.

For how to replace the motor core, please check video below:

Bafang M400 G330 G33 motor sealing gasket; if you open your motor, the gasket would be violated, then you may need a new gasket.  

Bafang MAX drive m400 G330 chainwheel- 38T; Bafang M400 fatbike chainwheel;

Bafang M300 M200 motor share the same MTB chainwheel with M400 motor.